Automatic Antenna Tuner 120W 54MHz Coverage Auto Ham Radio Recording Equipment

Description

Automatic Antenna Tuner 120W 54MHz Coverage Auto Ham Radio Recording Equipment
Description
he mAT-30 is an automatic tuner intended for use with modern Yaesu transceivers.It works with some Yaesu transceiver that supports an FC-30,FC-40 or FC-50 Yaesu tuner; a partial list of compatible units includes:FT-100,FT-857,FT-897,FT-450D,FT-891.The interface cable is included. The operating is the same as the method of the Yaesu tuner, which is simple and convenient. The mAT-30 can work within the range of 3MHz to 54MHz.
The mAT-30 connects to the radio via its CAT/LINEAR jack to control the tuning cycle;the transceivers Tune button controls the tuner.The CAT/LINEAR jack also powers the tuner,so it requires no external power supply.The mAT-30 is specially engineered to integrate with your Yaesu FT-100/857/897/450D/891 HF radio.Tuning is performed when the TUNE button is pushed
on the front of the transceiver and held for one second.
The mAT-30 provides automatic antenna tuning across the entire HF spectrum plus 6 meters, at power levels up to 120 watts.It will tune dipoles, verticals, Yagis, or virtually any coax-fed antenna. It will match an amazing range  of antennas and impedance, far greater than some other tuners you may have considered, including the built-in tuners on many radios.
The mAT-30 is specially engineered to integrate with your Yaesu FT-100/857/897/450D/891 HF radio. The mAT-30 connects to the CAT(Computer Automated Transceiver) port on the back of the radio. The CAT interface allows an external device such as a PC or the mAT-30 to control the FT-100/857/897/450D/891 by sending it serial commands. The mAT-30 takes advantage of this interface to simplify the tuning process --one button push is all that is needed in order to switch the radio to FM mode,reduce output power, transmit a carrier, measure the transmit frequency, and then restore the radio to its previous mode and power level!
The mAT-30 also features advanced memory tuning, providing 16000 memory locations; when tuning near a previously used frequency it will recall the settings for nearly instant tuning. It learns your favorite frequencies and bands as you use it.You can also start a tuning cycle manually whenever necessary.
The mAT-30 has16,000 frequency memories.When tuning on or near a previously tuned frequency,the mAT-30 uses "Memory Tune" to recall the previous tuning parameters in a fraction of a second.If no memorized settings are available,the tuner runs a full tuning cycle, storing the parameters for memory recall on subsequent tuning cycles on that frequency. In this manner, the mAT-30 "learns" as it is the bands and frequencies as it goes.
Specifications:
0.1 to 120watts SSB and CW peak power,30 watts on PSK and digital modes,and 100 watts on 6 meters.
Latching relays for ultra
Low power operation.
16,000 memories for instantaneous frequency and band changing.
Controlled from YaesuTUNE button on radio.Powered from Yaesu radio.
Works with most Yaesu radios that are FC-30,FC-40 or FC-50 compatible.
Partial radio list: FT-100,FT-857,FT-897,FT-450D,FT-891.
Tuning time:0.1 to 5 seconds full tune,0.1 seconds memory tune.
1.8 to 54.0 MHz coverage. Built-in frequency sensor.
Tunes 5 to 1500 ohm loads.
For dipoles,verticals,Vees,beams,long wire or any coax-fed antenna.
Includes interface cable.
Dimensions:20x13x4cm (LxWxH).
Weight:0.8Kg
AN IMPORTANT WORD ABOUT POWER LEVELS:
The mAT-30 is rated at 125 watts maximum power input at most. Many ham transmitters and transceivers, and virtually all amplifiers, output well over 125 watts. Power levels that
significantly exceed specifications will definitely damage or destroy your mAT-30.
If your tuner fails during overload, it could also damage your transmitter or transceiver. Be sure to observe the specified power limitations
Package Included:
1 x mAT-30 HF-SSB Automatic Antenna Tuner
1 x Connecting cable