SAE J1100 PDF

SAE J This standard provides a system of a defined nomenclature to describe vehicle dimensions. A. combination of letters and numerals helps the. This SAE Recommended Practice defines a set of measurements and standard procedures for motor vehicle dimensions. The dimensions are primarily intended . 26 May BY ORDER OF THE EXECUTIVE DIRECTOROffice of the Federal RegisterWashington, Authority of the Code of Federal Regulations.

Author: Gora Vucage
Country: Rwanda
Language: English (Spanish)
Genre: Politics
Published (Last): 13 December 2006
Pages: 156
PDF File Size: 16.77 Mb
ePub File Size: 20.48 Mb
ISBN: 304-3-24658-580-7
Downloads: 19758
Price: Free* [*Free Regsitration Required]
Uploader: Takasa

The Luggage Compartment Lid or access door must close and lock freely without forcing or excessive slamming with all of sae j1100 cargo modules in place in the compartment. The sae j1100 limit is sea rear side of rear of the front seatback, and a vertical plane tangent to and extending sae j1100 the front seatback. If no arm rest is provided at the designated “X” plane, use a height of mm above the SgRP. V1 Luggage Capacity 9.

All sqe dimensions define the proportional shape of the vehicle, as opposed to its designed pieces. See Figures 6, 7, sae j1100, and The code is interpreted as follows: Four-Door Models — Same as L1 8 b.

H Zero Z plane to ground – front 7. Pieces from subsequent Standard Luggage Sets may sae j1100 used when the previous set is placed in the Luggage Compartment. If the j100 is forward of the brake, the dimension is negative.

Cargo Volume Sae j1100 Input values are mm inches. Dimension shall be sae j1100 from the back of the cab to the forward edge of the mattress support surface. Dimension Revised Section No. L11 Accelerator heel point to steering wheel center X 6.

General— The dimensions in this report will enable the measurement sae j1100 a vehicle as designed. For vehicles with SgRP to heel H30 greater than mm, the accelerator pedal may be depressed as specified by the sae j1100.

Includes the front door, rear door, vents, and rear-quarter windows on both sides of the vehicle. These Vehicle Weights are established to enable uniform static comparisons of dimensions affected by the ground plane and vehicle pitch attitude. H Front seatback to j110 floor height 8. H Rear opening height 8. L Cargo body overall length 8.

Exterior components are projected horizontally to the exterior glazing surface see Sae j1100 3.

Cargo Dimensions — See Figures 24 through If the second seat is adjustable, it should be positioned at the SgRP and at a back angle as specified by the manufacturer. Hi1 Entrance height – front 6. Sae j1100 prefix T is added to the L length and H height to denote specific H-Point travel path dimensions.

H70 SgRP – front – Z coordinate 6. Design H-Point Travel Path H Headlamp to ground 7. This measurement includes vertical adjustment independent of track rise. Track rise, when provided, is the amount the H-Point increases in height with forward movement due to an inclined seat track. In the case of dual rear sae j1100, the dimension will be taken at centerline between the rear wheels.

Rearmost-Highest Design H-Point— The rearmost ‘location of the full sae j1100 position of vertical travel independent of track rise. X, Y, Z coordinates are dimensioned to their respective planes. For rear-facing third seat, measure from sae j1100 trimmed seat back at a height tangent to the top of the third Seat Cushion surface, rearward to the interior sae j1100 closure.

Scope— This SAE Recommended Practice defines a uniform set of interior and exterior dimensions for passenger bars, multipurpose passenger vehicles, and trucks. All other adjustable features, such as an adjustable steering wheel and adjustable seat height, a seatback that adjusts sae j1100 from the Seat Cushion, power 4-way or 6-way seats, etc.

The right pivot is with the right foot lined up on the accelerator and the left pivot is with the left foot on the floor in line with the clutch pedal.

The forward limit is the rear side of the second seatback or the folded third seat. H Seat Cushion sae j1100 – front 6.

Full text of “SAE J Motor Vehicle Dimensions”

Liters ft 3 Eq. H26 Interior body height – front at zero Y plane 6. W3 Sae j1100 room sae j1100 front 6. L55 Fiducial mark no. Fiducial Mark Dimensions 5. These are holes, surfaces, marks, or indentations on the vehicle body as described by the manufacturer.

SAE J1100: Motor Vehicle Dimensions

Has X, Y, Z coordinates established relative to the designed vehicle sae j1100, c. Establishes the rearmost normal design driving or riding position of sae j1100 designated seating position which includes consideration of all sae j1100 of adjustment, horizontal, vertical, and tilt, in a vehicle, b.

Opaque sae j1100, reveal or garnish moldings adjoining the interior glazing j1100 are projected normal and outward to the exterior glazing surface. W width and H height codes to denote specific pedal dimensions. The Torso Line is parallel to the straight flat portion of the lower back on the torso and is used to facilitate the definition of torso angle. They may be loosened and moved to the limits of the attaching hardware and then retightened to attain the most advantageous position.

The dash panel is usually the vertical extension of the toe panel. Search the history of over billion web pages on the Internet.

For vehicles with more than three seats, specify seat location along with dimension.